Teledyne-lecroy Voyager Exerciser Generation Script Language Manua Manual do Utilizador Página 19
- Página / 167
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Teledyne LeCroy Voyager USB 3.0 Exerciser Generation Script Language Reference Manual
10
PortCfgAck
Specifies whether the Exerciser responds to Port Config LMPs or not.
Example: Set PortCfgAck = 0
Possible values are:
0 # Do not respond to PortConfig LMPs.
1 # Automatically respond to PortConfig LMPs.
Default value: 1
Applicable Mode: HOST, DEVICE
LTSSMSettings
LTSSM Setting flags.
Example: Set LTSSMSettings = CUSTOM_TS1
Possible values are any combinations of the following flags:
0 # AUTO.
DISABLE_LFPS = 0x1 # Disable Polling.LFPS detection.
CUSTOM_TSEQ = 0x2 # Send specified number of TSEQ
(TSEQNumber setting), then go to the next state.
CUSTOM_TS1 = 0x4 # Send TS1 for specified period of time
(TS1Time setting), then go to the next state.
CUSTOM_TS2 = 0x8 # Send TS2 for specified period of time
(TS2Time setting), then go to the next state.
DISABLE_IDLE = 0x10 # Disable Logical Idle handshake, so LTSSM
jumps over relevant sub-state.
Default value: 0 (auto)
Applicable Mode: DEVICE, HOST
TSEQNumber
Specifies number of TSEQ Ordered Sets to be sent in Polling.RxEQ
sub-state. Applies only if CUSTOM_TSEQ bit is set in the
LTSSMSettings setting.
Example: Set TSEQNumber = 64000
Possible values are any values from 0 to 65535 (0xFFFF).
Default value: 65535
Applicable Mode: DEVICE, HOST
TS1Time
Specifies the time in nanoseconds to stay in the Polling.Active or
Recovery.Active sub-states, regardless of received pattern. Applies
only if bit CUSTOM_TS1 of the LTSSMSettings is set.
Example: Set TS1Time = 2000
Possible values are from 0 to 5000000 (5 ms). It is recommended not
to use values < 267 ns (required time for sending 8 TS1s)
Default value: 1000 (1 us)
Applicable Mode: DEVICE, HOST
TS2Time
Specifies the time to stay in the Polling.Active or Recovery.Active
sub-states, regardless of received pattern. Applies only if bit
CUSTOM_TS2 of the LTSSMSettings is set.
Example: Set TS2Time = 1000
Possible values are from 0 to 5000000 (5 ms). It is recommended not
to use values < 267 ns (required time for sending 8 TS2s)
Default value: 1000 (1 us)
Applicable Mode: DEVICE, HOST
- Voyager™ USB 3.0 Exerciser 1
- Document Disclaimer 2
- Trademarks and Servicemarks 2
- Copyright 2
- Version 2
- Contents 3
- 1 Introduction 10
- 1.1 Declaration Conventions 11
- 2 Script Language Structure 12
- 3 Comments 13
- 4 File-Including Directives 14
- 5 Constant Declarations 15
- 6 Data Pattern Declarations 16
- 7.1 Device Mode Settings 17
- 7.3 Link Delay Settings 22
- 7.5 LFPS Settings 26
- 7.6 Link Error Settings 29
- 7.9 Framing Error Settings 34
- 7.10 Script Parser Settings 37
- 8.2 Field Definitions 41
- 8.2.8 Defining Subfields 47
- Declarations 49
- ':' directive 54
- Attribute 58
- 8.5.2 Another Example 59
- 9 Generation Procedures 61
- 9.2.5 AddDrive Instruction 75
- 9.3 Send Packet Instruction 77
- FirstByte : 0,8 = { 01 } 78
- 9.5 Instruction Parameters 79
- 9.9 TxSleep Instruction 88
- 9.10 SendFile Instruction 89
- 9.11 Wait Packet Instruction 89
- 9.13 Wait Event Instruction 93
- 9.14 Loop Instruction 94
- 9.15 BreakLoop Instruction 95
- 9.16 Exit Instruction 96
- 9.17.4 Trace Instruction 100
- 9.17.5 Trace_B Instruction 101
- , len] = 0xAA 107
- ] = 0xAA 107
- -95 is padded with zeroes 107
- 63-72 109
- Assignments 111
- 10.11 Sizeof Operators 118
- 10.15 Forward Declarations 121
- 10.16 RAND Token 123
- Procedure Insertions 125
- 10.21 Name Aliasing 139
- "\" automatically 141
- 11.1 Example Script 1 142
- 11.2 Example Script 2 148
- 12.1.1 SKP_TIMER 151
- 12.1.2 PM_ACCEPT_MODE 152
- 12.1.3 CORRUPT_LC 152
- 12.1.4 CORRUPT_LMP 153
- 12.1.5 CORRUPT_SHP_FRAMING 155
- 12.1.6 CORRUPT_SDP_FRAMING 156
- 12.1.7 CORRUPT_END_FRAMING 156
- 12.1.8 CORRUPT_SLC_FRAMING 157
- 12.1.9 DELAY_LAU 159
- 12.1.11 LTSSM_SETTING 161
- 12.1.13 LTSSM_HOTRESET_TIME 163
- Reserved 164
- HotReset Time 164
Manuais e produtos relacionados com Equipamento Teledyne-lecroy Voyager Exerciser Generation Script Language Manua
Equipamento Teledyne-lecroy WaveStation 3000 Getting Started Guide Manual do Utilizador
(12 páginas)
(12 páginas)
Equipamento Teledyne-lecroy WaveStation SCPI Command Reference Manual Manual do Utilizador
(32 páginas)
(32 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais